Warning E11
说明：
由于版本不兼容性，主机软件版本L0-A-1.0.129、L0-A-1.0.133、L0-A-1.0.134不兼容手柄软件版本L4-A-1.0.001(或基于此版本定制版本) 。维修前请核对是否为使用此版本搭配导致。
a) 此故障代表“与手柄通讯异常”。
b) 可以通过尝试更换手柄来缩小诊断范围。
c) 如果判断为主机问题，且检查手柄显示屏或指示灯有显示，则检查主机主控板P5.7、P5.8与主机端手柄插口，是否断线或接触不良。
d) 如果判断为主机问题，且检查手柄显示屏或指示灯无显示，则检查主机主控板P5.6、P5.10与主机端手柄插口，是否断线或接触不良；P5.6、P5.10之间电压应为DC5V。
e) 如果判断为手柄问题，且检查手柄显示屏或指示灯无显示，则手柄供电异常。检查手柄控制板P1.1、P1.6与手柄端手柄插口，是否断线或者接触不良。
f) 如果判断为手柄问题，且检查手柄显示屏或指示灯有显示，则可能为通讯异常。检查手柄控制板P1.4、P1.5与手柄端手柄插口，是否断线或者接触不良。
g) 如仍不能解决问题，则尝试更换主机主控板或手柄控制板。
Note:
In light of the incompatibility of version, main console software versions L0-A-1.0.129, L0-A-1.0.133 and L0-A-1.0.134 are incompatible with the handpiece software version L4-A-1.0.001 (or the customized version based on this version). Prior to maintenance, check whether it is caused by the version matching of this version.
a) This failure means the “abnormality of the communication with handpiece”.
b) Try to reduce the diagnosis scope by replacing handpiece.
c) If the problem is judged attributable to the main console and confirming there is the display in handpiece display screen or indicator lamp according to the check, check the socket of main control boards P5.7 and P5.8 of main console with handpiece at the main console end and confirm whether there is a broken line or poor contact.
d) If the problem is judged attributable to the main console and confirming there is no display in handpiece display screen or indicator lamp according to the check, check the socket of main control boards P5.6 and P5.10 of main console with handpiece at the main console end and confirm whether there is a broken line or poor contact.
e) If the problem is judged attributable to the handpiece and confirming there is no display in handpiece display screen or indicator lamp according to the check, check whether the handpiece power supply is abnormal. Check the socket of handpiece control boards P1.1 and P1.6 with handpiece at the handpiece end and confirm whether there is a broken line or poor contact.
f) If the problem is judged ascribed to the handpiece and confirming there is no display in handpiece display screen or indicator lamp according to the check, it may be caused by the communication abnormality. Check the socket of handpiece control boards P1.4 and P1.5 with handpiece at the handpiece end and confirm whether there is a broken line or poor contact.
g) If the problem still exists, try replacing main control board of main console or handpiece control board.
Note:
Related Articles
Warning W06
a) 此故障代表“手柄治疗头温度超出上限”，仅在ready状态下进行检测。 b) 如果手柄ready状态下不制冷或温度升高，请参照 手柄不制冷解决故障。 c) 如果手柄能够制冷，此项检测极有可能是手柄长时间以高能量出光导致的。重新按下ready按键后，可以继续使用。 d) 如果手柄制冷，长按“W06”5次后进入后台，输入密码“78652818”后，显示温度和实际不一致，则为手柄温度传感器故障，需检查传感器线束是否松动，如无问题则需更换手柄控制板。 ...Warning W08
a) 此故障代表“水箱温度超出上下限”，极有可能是手柄长时间以高能量出光导致的。此提示会在水箱温度恢复正常后自动消失。 b) 如果该故障提示很容易出现（持续工作1h以内就会出现），则考虑为仪器故障。 c) 首先查看水质检测板显示水温，如果未出现温度跳变现象，则排除温度传感器接触不良问题，否则需检查温度传感器或更换水质检测板。 ...Warning W08: temperature of water tank exceeds the scope
a) This failure means that “temperature of water tank exceeds the scope”. It is very likely to be caused by the long-time high-energy laser emission. The prompt will disappear automatically after water tank temperature is recovered. b) If the failure ...Warning W06: temperature of handpiece treatment head exceeds the upper limit
a) This failure means that “temperature of handpiece treatment head exceeds the upper limit”, and test should be implemented only under the ready state. b) If handpiece refrigeration fails or temperature is increased under the ready state, ...Warning E16: detection to laser emission current is too large/small
a) This failure means “current testing – laser emission current is tested too large/small”. Use it again after restarting the instrument. If this failure still occurs, find out the problem. At this time, continue the use by ignoring this problem. ...